T 90° equal pvc pn16 d50

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc-dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc-flexible, blackDimensionsPress connectors and pipes-Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63-Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations-Operating temperature max. 70 °C-Operating pressure max. 1.0 MPaHeating installations-Operating temperature max. 80 °C-Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Material: white plast

Extension- gunmetal- R-thread, Rp-thread

Viega 2315

Elbow 90°,internal and external thread

Elbow 90°- gunmetal- R-thread, Rp-thread

For building drainage, For site drainage

Viega awkward connection pipe with eccentric sleeve, for tolerance compensation for toilet drain connection, with lip seal.

Brass Press Coupling with a corrosion-resistant surface with stainless steel press cap for DHW and radiator systems, stop ring, pressure indicator, color code, guaranteed leaking if not pressed. Calibration-free.Only to be used with Uponor MLC, Uni Pipe Plus and Metallic Pipe Plus pipes and with Uponor approved press tool.

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings - DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site - hempen without roughening of the thread is possible.

Uponor elbow fitting 45° with a diameter of 50 mm

Henco 40 x 40 mm PVDF press elbow 45° for water-, heating- and cooling installations. Max. 16 bar.

The threaded pipe fittings of ISIFLO is produced of dezincification resistant brass alloy (DZR). Use for cold water or warm water (max 110 degrees centigrade), air, oil or gas. Running pressure up to 10 Bar. Cylindrical thread (ISO 228/1)

The threaded pipe fittings of Holmgrens Metall is produced of dezincification resistant brass alloy (DZR). Use for cold water or warm water (max 110 degrees centigrade), air, oil or gas. Running pressure up to 10 Bar. Cylindrical thread (ISO 228/1)

Uponor press composite coupling ppsu 50-50