Drains and odour traps in acc. with DIN EN 274 for washbasins and bidets - design versions and accessories.High-quality building technology with simple assembly.Visign universal and slotted valves with open cover or click-close cover.Space-saving odour traps for concealed and pre-wall mounting.Design versions.Bottle or pipe odour traps made of brass or plastic.Accessories for special installation situations.

Flow-optimised press connector system for drinking water installations in acc. with DIN 1988 and DIN 50930-6 as well as heating installations, tested in acc. with DVGW worksheet W 534.Press connectorsSafe and fast processing without calibration of the pipe ends through O-ring-free press technology in all dimensions. In this way, widening or calibration of the pipe-ends becomes superfluous and reduces the assembly times. The interaction between aerodynamic radii and minimal cross-section narrowings ensure the lowest pressure losses in press systems for multilayer pipes. This allows a smaller dimensioning of drinking water installations and reduces the pipeline volume.SC-ConturAll sizes with SC-Contur - connections, which remain unpressed become visible when the system is filled. The SC-Contur is certified and fulfils the requirements of DVGW worksheet W 534, point 12.14, connectors with forced leakage.During leakage tests with water, Viega guarantees the identification of unpressed connections in the pressure range 0.1 MPa-0.65 MPa, in the case of a dry leakage test with compressed air or noble gases from 22 hPa-0.3 MPa.MarkingGreen dot on the press connectionPipesRaxofix PE-Xc/Al/PE-Xc-dimensionally stable, oxygen-proof in acc. with DIN 4726, greyRaxofix PE-Xc-flexible, blackDimensionsPress connectors and pipes-Raxofix-PE-Xc/Al/PE-Xc: d 16/20/25/32/40/50/63-Raxofix PE-Xc: d 16/20Areas of application PE-Xc/Al/PE-XcDrinking waterHeatingRainwaterCompressed airAreas of application PE-XcRainwaterDrinking waterUse of the system for application areas other than those described here must be agreed with Viega Service Center.Operating conditionsDrinking water installations-Operating temperature max. 70 °C-Operating pressure max. 1.0 MPaHeating installations-Operating temperature max. 80 °C-Operating pressure max. 1.0 MPaIrrelevant of the direction of flow, mixed installations are permitted.NoteThe DVGW test mark is only valid f

Material: white plast

Extension- gunmetal- R-thread, Rp-thread

Viega 2315

Elbow 90°,internal and external thread

Elbow 90°- gunmetal- R-thread, Rp-thread

Viega awkward connection pipe with eccentric sleeve, for tolerance compensation for toilet drain connection, with lip seal.

Fittings with threads in acc. with DINEN 10226, Part 1, certified for drinking water in acc. with DIN 1988 and gas installations in acc. with TRGI 2008 (observe notes on the model), tested in acc. with DVGW worksheet GW 6 and GW 393.CertificatesGunmetal threaded fittings - DVGW-Reg.-No. DV-7401AO2957Threaded connectionsR-external thread, produced on site - hempen without roughening of the thread is possible.

Viega 94270G

Uponor elbow fitting 45° with a diameter of 50 mm

Long nipple in gunmetal with R-thread. R: 12, L: 200 mm

The threaded pipe fittings of ISIFLO is produced of dezincification resistant brass alloy (DZR). Use for cold water or warm water (max 110 degrees centigrade), air, oil or gas. Running pressure up to 10 Bar. Cylindrical thread (ISO 228/1)

The threaded pipe fittings of Holmgrens Metall is produced of dezincification resistant brass alloy (DZR). Use for cold water or warm water (max 110 degrees centigrade), air, oil or gas. Running pressure up to 10 Bar. Cylindrical thread (ISO 228/1)

Cap,

90° angle for insert with tip end, Ø32, in chrome PP/TPE plastic, female/male